linux-configuration

v1.0.0 — Mandatory rules for any task on this machine that touches Linux desktop configuration: GNOME Shell extensions, gsettings, themes, hotkeys, systemd user services, or a repository install.sh. R

SKILL.md

GitHub

Linux Desktop Configuration Guidelines

These rules bind every change that touches GNOME Shell, desktop settings, hotkeys, systemd user services, or any repository install.sh. Follow them exactly even when the user's prompt does not restate them. Never reach for a destructive shortcut — logout, gnome-shell --replace, killing the Shell — to "just make it apply". When a reload is genuinely required, use only the in-place X11 run-dialog reload described below, which preserves the running session.

Ownership boundary

This is the reusable Linux desktop and installer policy for every project that selects it. Project AGENTS.md files may document local component ownership, installer entry points, dependencies, and verification commands, but should not copy the clean-install, root-optional, reboot, or GNOME reload rules here. When project guidance and this skill disagree on the shared safety procedure, use this skill and retain only the project-specific exception if it is truly required and explicitly documented.

Apply Changes Silently (required default)

Most desktop changes need no GNOME Shell reload. Reloading flashes the panel, resets the overview and animations, and steals focus — it interrupts the human's active work. Only edited extension code requires it (next section). For everything else, use the narrowest command-line mechanism that takes effect live, in place, with no visible disruption:

Change Silent live mechanism
Hotkeys, org.gnome.desktop.* / org.gnome.shell.* keys, themes, app behavior gsettings set … — immediate in the running session
An extension's own settings (its GSettings schema, read at runtime) gsettings set / dconf write on that schema — applies live
systemd user service (trackers, daemons, helpers) systemctl --user restart <unit> — that unit only, no GUI flash
Enabling/disabling an extension (state, not code) gnome-extensions enable/disable <uuid> — runs in place

Always state the exact silent command you ran, and verify it took effect — read the gsettings key back, systemctl --user status, gnome-extensions info <uuid>.

Reboot and Poweroff Safety

Never invoke reboot, shutdown, poweroff, halt, systemctl reboot|poweroff, or their loginctl equivalents directly. When the user explicitly authorizes a genuinely required reboot or poweroff, route it through the setup framework's safe_system_action.sh reboot|poweroff, which must keep its audible 10→1 countdown, extended alert at 0, and a Ctrl+C/SIGTERM cancellation path before requesting the action.

  • Installer code calls the shared safe_system_action wrapper from linux_installation_scripts_functions/installer_helpers.sh — never a local sleep 10 reimplementation.
  • Runtime programs install and invoke the same helper as ~/.local/bin/safe-system-action.
  • Refuse the destructive action when the shared helper is unavailable.
  • Never execute the helper while developing, testing, deploying, or validating a change. Verify with static source checks, shell syntax checks, and mocked call-site tests only — a test must never reach a real reboot or poweroff.

Extension Code Changes (deploy, then in-place reload)

Editing a loaded extension's code (extension.js / installed files) still needs a fresh Shell process: the Shell imports each extension's JS once per process lifetime and caches the module. There is no sanctioned, non-disruptive hot-reload for edited source —

  • gnome-extensions disable && enable calls the cached module's disable/enable; it does not re-read the edited source.
  • The org.gnome.Shell.Extensions.ReloadExtension D-Bus method is locked down (like Eval) and refuses external calls.
  • A newly added extension directory is invisible to the running Shell until it reloads.

So: deploy the files from the console, verify the installed files and settings, then activate the new code with the reload that matches the session type — check echo "$XDG_SESSION_TYPE" (or loginctl show-session):

X11 — trigger GNOME's own run-dialog reload, which restarts the Shell in place while preserving the session, open windows, and enabled extensions:

xdotool key --clearmodifiers alt+F2
sleep 0.5
xdotool type 'r'
xdotool key Return

This is the same Alt+F2 r a human would type and the only sanctioned automated reload. Verify the result afterwards (below).

Wayland — there is no in-place run-dialog reload. Do NOT force one. Deploy and verify the files, then ask the user to log out and back in. Waiting for the user is always better than losing their open work.

Regardless of session type, never force changes through with any of:

  • gnome-session-quit / --logout / --force
  • loginctl terminate-session … / loginctl kill-user …
  • systemctl --user stop gnome-session* or similar unit stops
  • pkill -HUP gnome-shell, killall gnome-shell, or any Shell-ending signal
  • gnome-shell --replace — it can disrupt the session and leave user extensions globally disabled

After extension work, verify gsettings get org.gnome.shell disable-user-extensions is false and previously enabled extensions are still active.

A Shell reload is never needed when the change only affects a systemd user service or installer-side gsettings — restart just the affected unit and leave the GUI alone.

Clean Installation Compatibility

Every repository change must stay compatible with a clean installation through installation_scripts/install.sh and the repository's own install.sh. Do not rely on packages, files, settings, or manual steps that exist only on the current machine — add every required dependency, asset, configuration step, and migration to the installer so a fresh checkout reproduces the complete setup. Keep installation steps idempotent and verify the clean-install path for every change.

Root-Optional Installers (avoid sudo)

All project install.sh scripts must run sudo-free in user mode; only linux_installations_setup hard-requires root. When writing or modifying installers:

  • Default invocation is bash install.sh with no sudo. Root-only steps (apt install, udev rules, files under /etc or /usr) are skipped, collected in a SUDO_REQUIRED_STEPS list, and reported at the end with the exact sudo command to apply them.
  • When invoked via sudo (clean-install chain), use a run_as_target helper (sudo -H -u "$TARGET_USER" env …) so user-level work lands in the desktop user's session, never in root's home.
  • Prefer user-level mechanisms that need no root at all: gsettings; GNOME extensions in ~/.local/share/gnome-shell/extensions/ (user-owned — patch and reconfigure without root); gnome-extensions enable/disable; systemctl --user units; files under $HOME (~/.claude, ~/.config, ~/.local).
  • sudo is genuinely required only for package management (apt), system-wide extension dirs (/usr/share/gnome-shell/extensions/), and root-owned paths (/etc, /usr/lib, udev rules).
  • Never bake an unconditional sudo into a step that a non-root run will hit; it stalls unattended/agent runs on a password prompt.