q2030-hv

Compute the high-voltage provisions an electrical harness owes under ECSS-Q-ST-20-30C section 6.20 and its IPC section 20 basis. Use when the task is sizing clearance and creepage at a harness termina

SKILL.md

GitHub

ECSS Harness Manufacturing — High-Voltage Application (space-systems/ecss/q2030-hv)

Use when the task is the high-voltage provision of ECSS-Q-ST-20-30C section 6.20, which binds the high-voltage section of the IPC/WHMA-A-620 acceptance basis — sizing the clearance and creepage a harness termination owes at its working voltage and operating pressure, grading what was actually built, and setting the proof test that demonstrates it.

Domain quick reference

  • The provisions have an entry condition. Below the high-voltage threshold a termination is graded by the ordinary acceptance criteria and owes no clearance, creepage or proof test under this section; applying them anyway adds stress and cost without adding evidence.
  • The insulating medium follows the pressure, and it does so non-monotonically. Well above the Paschen minimum the medium is air and its breakdown gradient falls roughly with pressure, so a cabin or a launch ascent is worse than the ground. Well below it the residual gas cannot sustain an avalanche and the limiting mechanism becomes flashover along the insulating surface, at a far higher gradient. Between the two lies the band where the breakdown voltage of air passes through its minimum.
  • Inside that band no practical spacing holds off a high voltage. The answer is not a larger gap: it is encapsulation, potting or a pressurized enclosure, so that the band is never the medium the feature is asked to work in. A feature sized by a gap there has been sized against a curve it is not on.
  • Clearance and creepage are different paths and are sized differently. Clearance is through the medium and follows the breakdown gradient; creepage is along an insulating surface and follows the tracking performance of the material and how dirty the surface is allowed to get. Creepage is never allowed to be shorter than the clearance it parallels, because the surface path would otherwise be the weaker of the two.
  • The proof test is derived, not chosen. Its voltage comes from the working voltage, its dwell has to be long enough for a weakness to show, and the leakage current during the dwell is the measurement that actually says whether the insulation is sound.

Workflow

  1. Validate the feature record: identifier, working voltage, operating pressure, insulating material group, contamination category, encapsulation flag, as-built distances and the proof-test record. A non-positive voltage or pressure, or an unknown material group or contamination category, is an input error, not a case to clamp.
  2. Decide whether the high-voltage provisions apply at this working voltage and report a feature below the threshold as not applicable rather than as compliant by accident.
  3. Pick the insulation regime from the operating pressure, then take the breakdown gradient of that regime — pressure-derated air above the band, surface flashover below it.
  4. Raise the encapsulation finding for an unencapsulated feature inside the band, and do not size a gap for it: there is no gradient there to size against.
  5. Size the clearance from the working voltage, the gradient and the safety factor, with a floor no feature goes below.
  6. Size the creepage from the working voltage, the material group and the contamination category, with its own floor and never below the clearance.
  7. Grade the as-built distances, derive the proof voltage and grade the applied voltage, dwell and leakage, absorbing representation error at each limit with a named tolerance rather than by widening it.

Pitfalls

  • Sizing a gap for a feature that operates inside the Paschen minimum band. The curve has no usable gradient there, so a larger gap buys nothing; encapsulation or pressurization is the only answer.
  • Using the sea-level breakdown gradient for a feature that flies. The gradient falls with pressure across the air regime, and the ascent profile passes through the worst of it.
  • Treating vacuum as free insulation. The gas stops breaking down, but the surface does not, and a contaminated or tracked surface flashes over well below the clean-surface gradient.
  • Sizing creepage without the material and contamination inputs. The same voltage on the same geometry needs very different surface paths on a high-tracking-performance material in a controlled environment and a poor one in a dirty one.
  • Accepting a proof test that reached a voltage someone picked. The level comes from the working voltage, and a short dwell or an unrecorded leakage current leaves the test without its measurement.

Behavior contract (gate 3)

The feature validation, applicability threshold, pressure-regime selection and gradient derivation, encapsulation finding, clearance and creepage sizing with their floors and the creepage-not-below-clearance rule, as-built grading and the proof-voltage, dwell and leakage checks are exercised by the gate 3 contract test: scripts/test_q2030_hv.py against scripts/q2030_hv_logic.py (stdlib unittest, offline). Run: python3 scripts/test_q2030_hv.py

Compliance

  • ECSS standards are freely downloadable (ESA); cite the source and paraphrase per standards-map.yaml.
  • compliance: STANDARDS-REF, gated: false.