e1012-sel
Use when compute heavy-ion and proton/neutron single-event latch-up (SEL) and single-event snapback (SESB) rates for a spacecraft electronic device under ECSS-E-ST-10-12C §9.4.1.4–9.4.1.5: fit a Weibu
SKILL.mdskills/space-systems/ecss/e1012-sel/SKILL.md
GitHubECSS Space Environment — SEL/SESB Rate Prediction (space-systems/ecss/e1012-sel)
Use when the task is predicting the single-event latch-up (SEL) or single-event snapback (SESB) rate for a spacecraft electronic device per ECSS-E-ST-10-12C §9.4.1.4–9.4.1.5 — fitting measured cross-section data, integrating over the mission particle environment, and categorizing the combined rate against acceptance thresholds.
Domain quick reference
- SEL (Single-Event Latch-up): a high-current state triggered in a CMOS device when a heavy ion or high-energy proton/neutron deposits sufficient charge in the parasitic thyristor structure to switch it on. Left unmitigated it can destroy the device. It is characterised by a threshold LET (heavy-ion path) or threshold proton energy (proton path) below which the event cannot occur.
- SESB (Single-Event Snapback): an analogous high-current state in n-channel MOSFETs triggered by impact ionisation; treated with the same rate methodology as SEL.
- Heavy-ion cross-section vs LET is modelled by a Weibull curve: σ(L) = σ_sat × (1 − exp(−((L − L_th)/W)^s)) for L > L_th, else 0. Parameters (L_th, σ_sat, W, s) come from measured heavy-ion test data (e.g. a Brookhaven or GSI heavy-ion facility run).
- Proton/neutron cross-section vs energy is modelled by the Bendel two-parameter formula: σ(E) = B × (1 − exp(−0.18 × (18/A)^0.5 × (E−A)))^4 for E > A, else 0. Parameter A is the threshold energy (MeV) and B is the asymptotic cross-section (cm²/device).
- The mission rate for each particle type is the integral of (cross-section × differential particle flux) over the relevant variable (LET or energy), computed numerically via the trapezoidal rule over the environment spectrum supplied by the ECSS-E-ST-10-04 environment model.
- Thresholds for rate categorization (per §9.4.1.5):
- acceptable: combined rate < 1×10⁻⁷ events/device/day
- monitor: 1×10⁻⁷ ≤ rate < 1×10⁻⁵ events/device/day
- critical: rate ≥ 1×10⁻⁵ events/device/day (latch-up protection required)
Workflow
- Obtain heavy-ion test data for the device and fit a Weibull curve (four parameters: L_th, σ_sat, W, s) to the measured cross-section vs LET points. If only a single-parameter fit is available, derive the remaining Weibull parameters from the given effective fluence test data. Reject any device for which no heavy-ion characterisation data exist.
- Obtain the mission differential LET spectrum (particles/(cm²·day· (MeV·cm²/mg))) from the approved environment model for the orbit and solar condition. Integrate the Weibull cross-section over this spectrum using the trapezoidal rule to obtain the heavy-ion SEL/SESB rate (events/device/day).
- Obtain Bendel parameters (A, B) for the device from proton test data or the literature. Obtain the mission differential proton energy spectrum (particles/(cm²·day·MeV)) from the same environment model. Integrate the Bendel cross-section over this spectrum to obtain the proton/neutron SEL/SESB rate.
- Sum the heavy-ion and proton rates into a combined rate.
- Categorize the combined rate: acceptable / monitor / critical per the thresholds in the domain quick reference. Flag any device in the monitor or critical band; a critical result mandates latch-up current limiting and power-cycle recovery circuitry.
- Check dominance: if one particle type contributes more than 10× the other, flag it for review — spectrum coverage or model applicability may need re-examination before closing the assessment.
Pitfalls
- Using a single-point saturation cross-section without fitting the full Weibull curve: this overestimates the rate at LET values just above the threshold (where the cross-section is still rising) and can give a pessimistic result that invalidates an otherwise acceptable device.
- Treating the Bendel model as universally applicable to every CMOS technology: the model was derived for bipolar devices; for advanced CMOS nodes the direct ionisation path from proton recoils may dominate, and the cross-section must then be measured rather than inferred.
- Summing heavy-ion and proton rates without checking which environment model was used for each: LET spectra and proton spectra must come from the same orbit epoch and shielding assumption, otherwise the combined rate mixes inconsistent environments.
- Interpreting a zero computed rate as automatically acceptable: a zero result usually means the spectrum did not extend above the device threshold; verify that the spectrum spans the full relevant LET or energy range before concluding the device is safe.
Behavior contract (gate 3)
The Weibull cross-section fit, Bendel proton model, trapezoidal rate integration, severity categorization, and combined assessment logic are exercised by the gate 3 contract test: scripts/test_e1012_sel.py against scripts/e1012_sel_logic.py (stdlib unittest, offline). Run: python3 scripts/test_e1012_sel.py
Compliance
- ECSS standards are freely downloadable (ESA); cite the source and paraphrase per standards-map.yaml.
- compliance: STANDARDS-REF, gated: false.